What is the master code for Kwikset pl1?

Make sure it unlocks the door. The default Mastercode is 0-0-0-0 . It is recommended that you change it to a code of your own. The lock is pre-programmed with a default User Code of 1-2-3-4.

What is the password for the Kwikset lock?

A User Code is used to unlock the door while a Mastercode is a password for making changes to the lock features . Interior of door You will reset your User Code to 1-2-3-4 and Mastercode to 0-0-0-0 when the reset is complete. Note: Each button represents two numbers (i.e. ONLY push the button once for 0).

What if I lost my Kwikset master code?

If you do not have the master or user code you may do a factory reset on the unit to program a new master code into the lock .

What is the default code for Master lock?

The factory-set combination is 0-0-0-0 . Turn the shackle 90° counterclockwise. Press the shackle down while turning the shackle another 90° counterclockwise. Set the dials to your new combination.

How do I reset my Kwikset pin?

Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button. 2. Press the PROGRAM button twice, enter the same or a new code and then press the LOCK button once . If your old code still remains in the unit, you will need to perform a hard reset of the unit.

What is the user code for Kwikset?

If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps. Note: If the lock is muted, you will not hear the lock beeping. Delete User Codes:The lock is pre-programmed with a default User Code of 1-2-3-4 .

How many digits is a Kwikset lock code?

It will be between 4-8 digits . The programming code cannot be the same as any user code.

Is there a master key for Kwikset locks?

Key management is now easier! Thanks to the two-cylinder Key Control Deadbolt with SmartKey Security, you can have one master key for all your units and unique keys for all of your tenants.

KWIKSET PL1 USER MANUAL Pdf Download (2024)

Download Table of Contents Contents Print this page

Manuals
Brands
Kwikset Manuals
Locks
PL1
User manual

Electronic deadbolt lock

Hide thumbs

Table Of Contents 17

Contents
Table of Contents
Troubleshooting
Bookmarks

Table of Contents

Installation Instructions
Drill Holes
Install Latch
Install Strike
Install Keypad Assembly
Install Inside Mounting Plate
Identify Door Handing
Adjusting Turn Piece
Specifications/Functions
Low Battery
Audio Indicator
LED Indicator
User Code
Delete Individual User Code
Delete All User Codes at Once
Temporarily Disable All User Codes
Function Programming
Code Protection Function
Detect Left / Right Hand Door Installation
Add New User Code
Simple Troubleshooting
Set Autolock Time Delay
Toggle Mute On/Off
Enable/Disable All User Code
Déclaration de Garantie Limitée
Manuel de L'utilisateur

Advertisem*nt

Available languages

ENGLISH, page 1

Limited Warranty Statements

1. Warranty

The manufacturer warrants the Product to be free from defects in material and

workmanship for a period of 12 months from the original date of purchase.

If you discover a defect in the Product covered by this warranty,

we will repair or replace the item at our option using new or refurbished

components.

2. Exclusions

This warranty covers defects in manufacturing discovered while using the

Products as recommended by the manufacturer rather than occurred by

the act of God, and damages caused by misuse, abuse, and

unauthorized modification.

3. Limited Liability

The manufacturer will not be held liable for incidental or consequential

losses or damages to any act of God.

4. Reminder

Service requirement shall subject to the presentation of this Warranty Card.

The Warranty Card will not be reissued if lost.

Product : KEYPAD ELECTRONIC DEADBOLT LOCK

Purchase Date :

ELECTRONIC DEADB LT LOCK

USER MANUAL

Table ofContents

Advertisem*nt

Table of Contents

Related Manuals for Kwikset PL1

Locks Kwikset Powerbolt2 Installation Manual
Touchpad keyless entry (2 pages)
Locks Kwikset SmartCode 913 Installation Manual
Touchpad electronic deadbolt (21 pages)
Locks Kwikset SmartCode 912 Programming And Troubleshooting Manual
(12 pages)
Locks Kwikset Smartcode 914 Programming And Troubleshooting Manual
(17 pages)
Locks Kwikset SmartCode 914 User Manual
(26 pages)

Locks Kwikset Smartcode 910 Installation And User Manual
Touchpad electronic deadbolt (9 pages)
Locks Kwikset Kevo Convert Installation And User Manual
(16 pages)
Locks Kwikset SmartCode 909 Installation And User Manual
Touchpad electronic deadbolt (6 pages)
Fingerprint smart lock (47 pages)
Locks Kwikset HomeConnect 620 Frequently Asked Questions And Troubleshooting Manual
Keypad electric smart lock (9 pages)

Summary of Contents for Kwikset PL1

Page 1 Limited Warranty Statements 1. Warranty The manufacturer warrants the Product to be free from defects in material and workmanship for a period of 12 months from the original date of purchase. If you discover a defect in the Product covered by this warranty, we will repair or replace the item at our option using new or refurbished components.
Page 2 3. Install Latch KEYPAD ELECTRONIC DEADBOLT a. Insert the latch and ensure it is parallel to the door face. INSTALLATION INSTRUCTIONS Mark the outline of the faceplate, then take out the latch. Backset is a distance from door edge to centre of hole on door face.
Page 3 5. Install Keypad Assembly 8. Adjusting Turn Piece a. Make sure the latch bolt is retracted. Turn the turn piece to left for 45 degrees for a right-handed door. b. Please refer to the diagram below for Cylinder Installation. Turn the turn piece to right for 45 degrees Place deadbolt against keypad with tailpiece in horizontal for a left handed door.
Page 4 ■ Specifications/Functions 1.Battery  Four AA（1.5V）Alkaline batteries.  2.Low Battery 2-1 The batteries should be changed immediately once you see button 1 flashing in red   and hear constant beep sounds for about 10 seconds when press programming button. ...
Page 5 6.User Code 12.Unlock the door 6-1 The preset User Code is 1234. Please delete it and create your personal code The door can be unlocked by key or pressing User Code on keypad from outside or by before using lockset for the first time. interior turn-piece.
Page 6 ■ Function Programming 17.Code Protection Function Programming Code (PC) The operation will stop if unauthorized codes are entered over 5 times. USER Code (UC) The System will re-operate again after 45 sec. Detect Left / Right Hand Door Installation 18.Illumination Enter PC The LED Keypad will light up when pressing any button for easy operation in the dark.
Page 7 ■ Simple Troubleshooting Programming Code (PC) USER Code (UC) Situation 1 Set Autolock Time Delay After the installation of the lockset and batteries, the door cannot Enter Seconds be locked and three short beeps are emitted when you press the Enter PC (10~99) Programming button.
Page 8 ■ Situation 5 User Code & Function Set up The lock has been working normally, but suddenly, the latch bolt locks up, and the turn piece inside cannot be rotated, not even with 1. Leave door unlocked while programming. 2. Please run the door-handing identifying process (Refer to programming table) the key.
Page 9 Déclaration de garantie limitée 1. Garantie Le fabricant garantit que ce produit est exempt de tout vice de matériaux et de fabrication pour une période de 12 mois à compter de la date d'achat. Si vous découvrez que ce produit a un vice couvert par cette SERRURE garantie, nous réparerons ou remplacerons le produit à...
Page 10 3. INSTALLEZ LE VERROU SERRURE ÉLECTRONIQUE À PÊNE DORMANT a. Insérer le verrou dans le trou et ajustez-en la position de AVEC CLAVIER/DIRECTIVES D'INSTALLATION manière à ce qu'il soit parallèle à la surface de la porte. Tracez les contours de la plaque du verrou, puis retirez La distance d'entrée correspond à...
Page 11 5. INSTALLEZ LE CLAVIER DE LA SERRURE 8. AJUSTEMENT DU TOURNIQUET a. Assurez-vous que le pêne est complètement rétracté (désengagé). Faites pivoter le tourniquet à 45 degrés b. Regardez bien le schéma ci-dessous pour savoir comment installer le cylindre. vers la gauche si la porte ouvre vers la Insérez le cylindre dans la surface avant de la serrure en insérant la tige du cylindre, droite.
Page 12 ■ Spécifications et Fonctions  1. Piles Quatre piles alcalines AA ( 1,5V ) .  2. Lorsque les piles sont faibles   2-1 Les piles doivent être changées dès que vous voyez que le bouton 1 émet une lumière rouge clignotante et que vous entendez un «...
Page 13 5-3 Le code de programmation ne sert qu'à la configuration des fonctions de la serrure. 10-2 Vous pouvez utiliser le même code d'usager à usage unique plusieurs fois. Il devra Vous ne pouvez pas déverrouiller la serrure en entrant le code de programmation. être reprogrammé...
Page 14 ■ Programmation des Code de programmation (CP) 15-2 Cette fonction n'est pas activée par défaut lorsque vous utilisez la serrure pour la première fois. Vous devez l'activer manuellement si vous le souhaitez. Code d'usager (CU) fonctions 15-3 Le délai de verrouillage prédéfini est de 30 secondes. Vous pouvez définir le temps que vous voulez.
Page 15 ■ Code de programmation (CP) Dépannage simple Code d'usager (CU) Définition du délai de verrouillage automatique Situation1 : Après l'installation de la serrure et des piles, la porte ne peut Entrez les secondes Entrez le CP être verrouillée et trois bips courts sont émis lorsque vous appuyez (10 ~ 99) sur le bouton de programmation.
Page 16 Situation 5 : ■ Configuration des fonctions et des La serrure fonctionne normalement, mais tout à coup, le pêne se codes bloque, et le tourniquet à l'intérieur ne peut pas être mis en rotation, même pas avec la clé. 1. La serrure devrait demeurer déverrouillée lors de sa programmation. Causes : La détection de la position du loquet de verrouillage est anormale.

KWIKSET PL1 USER MANUAL Pdf Download (2024)

Available languages

Quick Links

Related Manuals for Kwikset PL1

Summary of Contents for Kwikset PL1

Table of Contents

Print

Rename the bookmark

Delete bookmark?

Delete from my manuals?

FAQs

What is the master code for Kwikset pl1? ›

References